3M Automobile Accessories 3M PPS Sun Gun Color Matching Light System User Manual

0

Out of 0 Ratings

Owner's of the 3M Automobile Accessories 3M PPS Sun Gun Color Matching Light System gave it a score of 0 out of 5. Here's how the scores stacked up:

  • Reliability

    0 out of 5

  • Durability

    0 out of 5

  • Maintenance

    0 out of 5

  • Performance

    0 out of 5

  • Ease of Use

    0 out of 5
of 14
 
To insert the 3M™ PPS™ SUN GUN™ Battery Pack into your 3M™ PPS™ SUN GUN™
Light, slide it into the end of the handle until it snaps securely into place. To remove the
3M™ PPS™ SUN GUN™ Battery Pack from your 3M™ PPS™ SUN GUN™ Light,
depress the release buttons on each side together, then withdraw the battery pack from
the 3M™ PPS™ SUN GUN™ light.
Refer to the Warning and Caution statements earlier in this manual for proper disposal
information. Do not disassemble 3M™ PPS™ SUN GUN™ Battery Pack. NOTE: To
prolong battery life, disconnect battery pack from the 3M™ PPS™ Sun Gun™ Light when
not in use.
Switch
Note: When connecting the 3M™ PPS™ SUN GUN™ Battery Pack to the 3M™ PPS™
Sun Gun™ Light, wait one second before depressing the switch to allow the internal
microprocessor to initialize. The switch operates as follows: Depressing the switch one
time turns the lamp on in standard brightness mode. Depressing the switch a second
time in succession boosts lamp brightness to “turbo mode.” Depressing the switch a third
time in succession turns the unit off. Note: Due to the intense heat associated with
halogen type lamps and as a safety precaution, the 3M™ PPS™ Sun Gun™ Color
Matching Light is configured with an automatic time-out feature. If the 3M™ PPS™ Sun
Gun™ Color Matching Light is left turned on in either standard or turbo mode, it will
automatically turn itself off after approximately 50 seconds.
In addition, if the 3M™ PPS™ SUN GUN™ Light is operated repeatedly in a short time,
heat build-up in the light may cause the fan to continue to operate for a short time after
the light goes off. This is to aid in cooling the interior of the light, and the light can be
used in this condition. If the light’s temperature continues to increase from continued
repetitive use, it may reach a condition in which the light will shut off, and the fan will
continue to run until the 3M™ PPS™ SUN GUN™ Light has cooled. During this cool-
down period, the light will not restart when the switch is pressed until the fan cools the
3M™ PPS™ SUN GUN™ Light sufficiently. This may take up to 15 minutes.
Important Safety Instructions for Battery Chargers
• SAVE THESE INSTRUCTIONS – This manual contains important safety
instructions for the 3M™ PPS™ SUN GUN™ Battery Charger. Before using the
3M™ PPS™ SUN GUN™ Battery Charger, read all instructions and cautionary
markings on the 3M™ PPS™ SUN GUN™ Light, Battery Pack, Battery Charger
and Power Supply.
CAUTION: Under certain conditions, when the charger plugged into the power
supply, the exposed charging contacts inside the charger can be shorted by contact
with foreign material such as, steal wool, aluminum foil. These conductive materials
and any buildup of metal particles should be kept away from charger cavities. Always
unplug the charger from the power supply when there is no battery pack in the cavity.
Unplug charger before cleaning.
Charger
The 3M™ PPS™ SUN GUN™ Battery Pack included with the 3M™ PPS™ SUN GUN™
Light can be charged in a 3M™ PPS™ SUN GUN™ Battery Charger only. Be sure to
read all Safety instructions before using charger.
Charging Procedure
1. Charge the 3M™ PPS™ SUN GUN™ Battery Pack for at least eight hours prior to
its first use.
2. The LED indicator on the Battery Charger operates as follows:
No Light No battery in charger
RED Battery in and rapid charging
GREEN Battery in and charging complete
RED/GREEN FLASHING Fault (low voltage or battery too hot)
3. If the 3M™ PPS™ SUN GUN™ Battery Pack is unused for long periods of time
between uses, it may not accept a full charge after the first charge cycle. Depending
on the time in storage and temperature during storage, several cycles may be
required to return the Battery Pack to 100% usable capacity. The Ni-Cd Battery Pack
recovery can take 1-3 cycles.
4. Best performance will be obtained if the battery pack is charged when the air
temperature is around 75F (24C). Do not charge the battery pack below 40 degrees
Farenheit (4.5C) or above 105 degrees Farenheit (40.5C)
Battery Installation and Removal
Before installing or removing the 3M™ PPS™ SUN GUN™ Battery Pack, read all
instructions and cautionary markings on the 3M™ PPS™ SUN GUN™ Light, Battery
Pack, Battery Charger and Power Supply.
5 6

   Find Your Products By Category