Campbell Hausfeld Electronic Keyboard Air Compressor User Manual

0

Out of 0 Ratings

Owner's of the Campbell Hausfeld Electronic Keyboard Air Compressor gave it a score of 0 out of 5. Here's how the scores stacked up:

  • Reliability

    0 out of 5

  • Durability

    0 out of 5

  • Maintenance

    0 out of 5

  • Performance

    0 out of 5

  • Ease of Use

    0 out of 5
of 4
 
– 2 –
Operation (Continued)
IN230000AV MODELS TL1002, TL1017 AND TL1049
EXHAUST PORT
ANVIL
OIL PORT
HOLE ON
BACK SIDE
FORWARD/
REVERSE
BUTTON
TRIGGER
REGULATOR
1/4" NPT FEMALE
AIR INLET
EXHAUST
PORT
OIL PORT
HOLE
FORWARD/
REVERSE
SWITCH
TRIGGER
REGULATOR
ANVIL
1/4" NPT FEMALE
AIR INLET
REVERSE
LEVER
REGULATOR
ANVIL
REMOVE
SCREW FOR
OIL PORT
HOLE
FORWARD
LEVER
EXHAUST
PORT
UNDER-
NEATH
1/4" NPT
FEMALE
AIR INLET
reverse directions for 20 to 30 seconds. Oil will
discharge from the exhaust port when air pressure
is applied.
Impact Mechanism Lubrication.
The impact mechanism should be lubricated monthly.
DISCONNECT THE IMPACT WRENCH FROM THE
AIR SUPPLY BEFORE LUBRICATING.
1. Disconnect the impact wrench from the air supply.
2. Remove the allen head screw from the oil port hole
on the right side of the tool that has "OIL" stamped
below the hole for model TL1002. For model TL1049,
the screw is located on the left hand side of the tool
near the exhaust port. For model TL1017, the screw
is located in front of the forward/reverse lever.
3. Put three teaspoons of Campbell Hausfeld air tool
oil in the oil port hole. Replace the screw.
4. Reconnect the air supply to the impact wrench and
run for 20 to 30 seconds. Lubricate the entire impact
mechanism by rotating the tool upside down and
sideways while running the tool.
5. Remove the screw and hold the oil port hole over a
suitable container to allow excess oil to drain.
6. If the oil is dirty, repeat the procedure above until
the oil comes out clear. Install the screw and
tighten. The residual oil remaining in the impact
mechanism chamber is all that is needed for proper
lubrication.
the air motor and the impact mechanism. Follow the
outlined procedures and refer to Figure 1 for details.
Campbell Hausfeld air tool oil (ST127000AV) is recom-
mended because this oil cleans, lubricates and inhibits
rust all in one step.
Air Motor Lubrication.
The motor must be lubricated daily. An air motor cannot
be oiled too often.
DISCONNECT THE IMPACT WRENCH FROM THE
AIR SUPPLY BEFORE LUBRICATING.
1. Disconnect the impact wrench from the air supply.
2. Turn the impact wrench upside down.
3. Simultaneously (at the same time), pull the trigger
and pour a teaspoon of Campbell Hausfeld oil in the
air inlet. Then, push the forward and reverse button
in both directions.
AFTER AN AIR TOOL HAS BEEN LUBRICATED,
OIL WILL DISCHARGE THROUGH THE EXHAUST
PORT DURING THE FIRST FEW SECONDS OF
OPERATION. THUS, THE EXHAUST PORT MUST
BE COVERED WITH A TOWEL BEFORE APPLY-
ING AIR PRESSURE. FAILURE TO COVER THE
EXHAUST PORT CAN RESULT IN SERIOUS IN-
JURY.
4. Connect the impact wrench to the air supply and
cover the exhaust port with a towel (See Figure 1).
Run the impact wrench in both the forward and
Figure 1 Impact Wrench Features
MODEL
TL1002
MODEL
TL1017
MODEL
TL1049
WARNING
!
!
WARNING
!
!
WARNING
!
!

   Find Your Products By Category